Rotel HDCD Single Play Compact Disc Player RCD-1072 Spécifications télécharger pdf (Page 13)

NAD C 542 Compact Disc Player

REAR PANEL CONNECTIONS

1. LINE OUTPUT

Connect a cable from these jacks to your amplifier. Plug one end

of a twin RCA-to-RCA lead into the L (upper) and R (lower) output

jacks. Connect the other end of the cable to your stereo amplifier’s

CD input, or to any other “line-level” input jacks (such as the

AUXiliary inputs). Do NOT connect this cable to the amplifier’s

PHONO input jacks. The RCA sockets on your NAD C 542 are

colour coded for convenience. Red and white are Right and Left

audio respectively, and yellow for NAD Link and Digital Out.

Ensure that leads and sockets are not damaged in any way and all

sockets are firmly pushed home.

2. DIGITAL OPTICAL & COAXIAL OUTPUT

The digital playback signal is available at this output jack. The

serial data output is taken after the error correction but before the

digital-to-analogue conversion and filtering. The output is

transformer-isolated from the built-in D-to-A circuits. It may be

connected to any digital signal processor that conforms to the

Sony/Philips (SPDIF) standard.

To use the digital output, connect a cable from this jack to the “CD

Digital” or equivalent input on a digital processor or recorder. For

QUICK START

best results, the cable should be a 75 ohm coaxial cable of the

type used for video signals, with an RCA phono plug at each end

or the cable should be an optical cable terminated with a TOS

Link connector. ( T o d istinguish them from similar phono-plug

c a b l e s u s e d f o r analogue audio signals, video and digital signal

cables often are colour-coded with yellow plugs.)

3. NAD LINK IN/OUT

The NAD-Link connector is used to pass commands from other units

fitted with NAD-Link connectors. This allows centralised control of a

complete system, and also allows some of the basic functions of

other NAD components (such as a tuner, or cassette-deck) also

equipped with NAD-Link to be controlled with an NAD system remote

control. To function with such other units, connect the C 542's NAD-

Link Out to the NAD-Link In on the other unit. NAD-Link connectors

can be daisy-chained, IN to OUT, so that a whole system can be

controlled from the remote control facilities of one unit.

NOTES: It is advisable not to connect NAD-Link if these units that

have their own built-in remote control command receiver and are

positioned together, in direct view from the remote control

handset. If you are unsure, try operating the products without

NAD-Link first; If the unit responds to the remote control

command, it will not be necessary to connect NAD-Link.

Never loop the last unit back to the first NAD unit in the NAD-Link

chain. Unplug all units from the mains before connecting or

disconnecting NAD-Link.

4. IR IN

This input is connected to the output of an IR (infrared)

repeater (Xantech or similar), or the IR output of another

component to allow control of the C 542 from a remote location.

Ask your dealer or custom installer for further details.

The 12V trigger Input allows the C 542 to be switched remotely

from STANDBY to ON and vice-versa by ancillary equipment such

as a pre-amp, AV processor etc. The controlling device must be

equipped with a 12V trigger output to use this feature.

7. AC LINE CORD

Connect this power cord to an AC mains wall outlet or to an AC

convenience outlet at the rear of your amplifier

When the switch is set to the OFF position, the unit ignores

any trigger In command. The front panel buttons and Power

On/Off buttons on remote control toggles between Power On

and Standby Mode. This is the correct setting for most

installations.

For control by an external 12V trigger signal, set the switch

to AUTO position, and the C 542 will Power On when the

trigger Input is high (12V present). In this setting, the front

panel and the remote control ON/STANDBY controls are

defeated; only the 12V Trigger Input can turn the C 542 ON.

The unit will go to Standby mode if the trigger goes from

high to low (no 12V present). The unit will not go to

standby mode using any button on front panel and remote

control. When the external power is first applied to the unit,

the unit will go to the status directed by Trigger input when

the switch is set to AUTO.

NOTE ON INSTALLATION

5. +12V TRIGGER IN

6. +12V TRIGGER SWITCH

Install the NAD C 542 Compact Disc player on a level, vibration-

free surface. (Severe vibration, or operation in a tilted position,

may cause the player to mis-track.) The player may be stacked

with other stereo components, as long as there is adequate

ventilation around it. If the player is placed in close proximity to

a radio tuner (AM or FM), a VCR, or a television set, the operation

of its digital circuits may produce static that would interfere with

reception of weak broadcast signals. If this occurs, move the CD

player away from other devices or switch it off when viewing or

listening to broadcasts.

Connect a twin RCA-to-RCA lead from the L (left) and R (right)

Line Output jacks to the corresponding CD inputs on your

amplifier.

Plug in the AC power cord.

Press the green POWER button to turn on the player.

Press OPEN to open the disc drawer.

Place a CD, label side up, in the tray’s circular recess. Be

certain that the disc is centred within the recess.

Press PLAY/PAUSE. The drawer closes automatically, and the

disc begins to play.

At any time you may press SKIP or to select different tracks on

the disc.

Press PLAY/PAUSE if you want to stop play temporarily while

keeping the pickup at its current position on the disc. Press

PLAY/PAUSE again when you want to resume playback. Press

STOP if you want to end play and reset the pickup to the

beginning of the disc.

1 2 ... 8 9 10 11 12 13 14 15 16 17 18

Commentaires sur ces manuels

Pas de commentaire

Rotel HDCD Single Play Compact Disc Player RCD-1072 Spécifications Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de CD Rotel HDCD Single Play Compact Disc Player RCD-1072