Rotel RSP-976 Manuel du propriétaire télécharger pdf (Page 18)

RSP-976 Surround Sound Processor

To change the Zone 2 input source:

1. Press the front panel ZONE button. The

status of Zone 2 appears in the display.

Make sure that Zone 2 is ON.

2. Within 10 seconds after pressing the ZONE

button, press one of the INPUT SOURCE

buttons to select a new source for Zone 2.

The name of the selected source appears

in the display.

3. Following 10 seconds with no commands,

the RSP-976 reverts to normal operation.

To change the Zone 2 volume:

1. Press the front panel ZONE button. The

status of Zone 2 appears in the display.

Make sure that Zone 2 is ON.

2. Within 10 seconds after pressing the ZONE

button, adjust the volume control to change

the Zone 2 output level. The new setting

appears in the display. This volume adjust-

ment is only available using the VARIABLE

output configuration. In FIXED output mode,

the volume control for Zone 2 is disabled.

3. Following 10 seconds with no commands,

the RSP-976 reverts to normal operation.

NOTE

: The volume and input source controls

described in this section are only available

when the RSP-976 is fully activated in the main

room (i.e. the display is visible). If the RSP-976

is turned off, you can only turn Zone 2 on or

off from the front panel. In this case, the ZONE

button is a simple toggle control – turning

Zone 2 on or off with each press of the but-

ton. When Zone 2 is on, the front panel

STANDBY LED flashes. When Zone 2 is off,

the STANDBY LED is steadily lit.

Controlling Zone 2 from the

Remote Location

With a properly configured IR repeater sys-

tem, you have full control of Zone 2 using an

RR-969 remote from the Zone 2 location. You

can select and operate a source, adjust the

volume, and turn Zone 2 on or off. Whatever

commands you send from the RR-969 will

change Zone 2 and only Zone 2, just as if

you were controlling a totally independent

audio system in that room. These changes will

have no effect on the main listening room.

To turn Zone 2 on or off, press the POWER

button

on the remote. To adjust the volume

in Zone 2, press the VOLUME buttons

the remote. To select a different analog input

source, press one of the INPUT SOURCE but-

tons

on the remote.

NOTE

: The volume adjustment is only avail-

able if the Zone 2 outputs are configured to

use VARIABLE levels. With FIXED levels, the

volume control for Zone 2 is disabled.

Zone 2 Audio Outputs

See Figure 5

These line-level RCA outputs send the Zone 2

audio signal to a stereo amplifier driving a

pair of speakers in the remote zone.

NOTE

: Only analog input signals are avail-

able at the Zone 2 outputs. Source compo-

nents connected to only the digital inputs are

not available in Zone 2.

Although you have the option of using an in-

tegrated amplifier or a receiver to power the

remote speakers, we suggest using a fixed-

gain power amplifier. This simplifies system

installation and operation. Your authorized Rotel

dealer may make another recommendation

based on specific system requirements.

To configure your system for Zone 2 opera-

tion, connect the left and right Zone 2

outputs

on the RSP-976 to the left and right channel

inputs

of the amplifier powering the remote

speakers, using standard RCA audio cables.

NOTE

: By default, the Zone 2 outputs provide

a VARIABLE level signal, with control of the

volume from the RSP-976 front panel and/or

remote control from Zone 2. Alternatively, you

can configure these outputs for FIXED level,

which disables the volume control and sends

a fixed line-level signal to an amplifier with

its own volume control. See the ON-SCREEN

DISPLAY/Configuration section for details.

ZONE REM. IN Jack

See Figure 5

This 3.5 mm mini-jack accepts signals from a

infrared repeater located in Zone 2. A third-

party IR repeater system is required for op-

eration of the RSP-976’s ZONE 2 functions from

the remote zone.

NOTE

ZONE 2 and its IR repeater must be in

a different location than RSP-976 to prevent

IR commands intended to control Zone 2 from

inadvertently controlling the main room op-

erations.

IR OUT Jacks

See Figure 5

The IR OUT 1 & 2 jacks send IR signals re-

ceived at the ZONE REM IN jack or the EX-

TERNAL REM IN jack to an infrared emitter

placed in front of a source component or to

Rotel CD players, cassette decks, or tuners with

a compatible rear panel IR connector.

This output is used to allow IR signals from Zone

2 to be sent to the source components, or to

pass along IR signals from a remote in the main

room when the sensors on the source compo-

nents are blocked by installation in a cabinet.

See your authorized Rotel dealer for information

on IR repeater systems.

NOTE

: The EXT REM IN jack located to the

right of these jacks is for use with an external

IR sensor duplicating the front panel IR sen-

sor and located in the primary zone. It should

not be used for ZONE 2 IR connections.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 55 56

Commentaires sur ces manuels

Pas de commentaire

Rotel RSP-976 Manuel du propriétaire Page 18

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Rotel RSP-976